November 4, 2026 - No. 44 In This Issue : NTSB Finds Learjet Elevator Pieces Miles From Impact Site : ACJ Survey Shows Growing Government Bizav Role : Israel's IAI on verge of winning $900 million deal for six refuelling aircraft for Indian Air Force (IAF): Reports : Rolls-Royce to develop efficient next-gen jet engines for single-aisle aircraft : Embraer names FL Technics as new Authorized Service Center for E-Jets in Lithuania : Navy Class A Aviation Mishaps Reach Decade High : FAA Orders DA40 Door Inspections After In-Flight Separations : Boeing still awaits major 777-9 test apprFAA issues directive to address Boeing 737 circuit breaker issueovals despite 2027 delivery target : FAA issues directive to address Boeing 737 circuit breaker issue : US Air Force wants AI to assist aerial refueling NTSB Finds Learjet Elevator Pieces Miles From Impact Site Investigators confirmed the control surface separated before impact, but its role in the fatal crash remains undetermined. Matt Ryan Tuesday, November 03, 2026 at 03:44 PM ET Verified Edited By: Matt Ryan [NTSB via YouTube] Key Takeaways: The National Transportation Safety Board (NTSB) confirmed Tuesday that portions of the left elevator from a Learjet 60 that crashed in Palm Beach County, Florida, on Sunday were found as far as 3.8 miles from the accident site. NTSB member Tom Chapman said investigators located most of the elevator in three pieces between 1.3 and 3.8 miles from the main wreckage. The discovery confirms that at least part of the aircraft’s tail separated before impact. Elevator Separation Confirmed Chapman said investigators will examine whether the elevator’s separation contributed to the accident or resulted from forces acting on the aircraft during its descent. “What that means exactly in terms of what caused the aircraft to lose control, or whether the loss of this piece was a result of the forces on the aircraft, we don’t know yet,” Chapman said during Tuesday’s briefing. “So it’s going to take some more analysis. But finding that piece is a very, very significant bit of evidence.” The Learjet was traveling from Austin, Texas, to the Bahamas when its crew reported icing and moderate turbulence before declaring an emergency. Chapman said weather remains a key focus of the investigation. Recovery Efforts Continue Investigators are continuing to recover additional wreckage from the water-filled impact crater near a roadway at the accident site. Chapman said crews removed an unstable utility pole Tuesday morning, allowing work to begin on stabilizing the crater. The NTSB expects access to the area as early as Wednesday and anticipates finding critical aircraft components beneath the water. Heavy rain and severe storms have complicated recovery efforts, while much of the wreckage recovered so far consists of small fragments that investigators have not yet identified. As the agency awaits further examination of the impact crater, it has begun to receive recordings and accounts from inidividuals who said they witnessed the accident. “I understand that we’ve now received dash cam footage and multiple eyewitness accounts that will help us better understand the condition of the aircraft and the circumstances of the crash,” Chapman said. Investigators are also reviewing maintenance and crew records for the Learjet as they work to reconstruct the aircraft’s final moments. ACJ Survey Shows Growing Government Bizav Role Airbus Corporate Jets research is showing a bump in interest in business aircraft from governments. A recent survey of 280 business aviation financiers and brokers worldwide found that 91% of respondents expect government interest in purchasing or chartering business aircraft to grow. This research highlights that business aviation has expanded beyond traditional executive transportation into multimission governmental roles supporting diplomatic travel, crisis response, humanitarian missions, medical evacuation, and repatriation, according to Airbus Corporate Jets. Survey respondents in the U.S. represented the highest proportion of those seeing increased government demand (95%), followed by the Middle East (94%), Asia (92%), Europe (88%), and Latin America (80%). About 50% of Airbus Corporate Jets’ customers are government entities, and the company believes this is a long-term growth market. “The findings demonstrate just how significantly the role of business aviation is evolving within government,” said Airbus Corporate Jets president Chadi Saade. “The current geopolitical environment has increased the need for governments to be able to move people quickly, securely, and reliably, often at short notice and into challenging operating environments.” Citing examples, the company noted that Germany’s special air mission wing operates a fleet of 18 aircraft—including ACJ319, ACJ321neo, and ACJ350 models—for government and patient transport roles. Another example is the Slovak government flight service, which operates two ACJ319s to support search-and-rescue and humanitarian missions. Israel's IAI on verge of winning $900 million deal for six refuelling aircraft for IAF: Reports NEW DELHI: Israel Aerospace Industries (IAI) is on the verge of winning a massive $905.7 million (approx Rs 8,000 crore) deal to convert six Boeing 767 passenger jets into refuelling tankers for the Indian Air Force (IAF), according to Israel media reports. Israel govt-owned IAI is a major aerospace and aviation manufacturer in the world that produces aerial and astronautic systems for both military and civilian usage. It has emerged as the sole qualifying bidder after rival proposals from Russian and European firms failed to meet evaluation criteria, as per the reports. If it wins the bidding, IAI will purchase six Boeing 767 aircraft for the purpose, with a commitment that at least 30% of the work on the refuelling tanker project will be done in India under the Make-in-India initiative. Hindustan Aeronautics Limited (HAL) is likely to be the Indian partner for the conversion work that includes local systems integration, wiring and structural updates. Deliveries are projected to span from around 2028 to 2030 following clearance processes IAI’s Multi-Mission Tanker Transport is based on pre-owned Boeing 767 passenger aircraft that are converted into military tanker and transport platforms by IAI’s Bedek Aviation Group. The new tankers will replace or supplement the IAF’s ageing fleet of Russian-origin Ilyushin Il-78 aircraft, boosting long-range mission endurance for fighters like the Rafale and Su-30MKI. Beyond mid-air refuelling, the aircraft will support strategic airlift, cargo movement and troop transport. IAI has more than 40 years of experience in air-to-air refuelling solutions and has done dozens of conversions to air-to-air refuelling for more than 12 customers worldwide including the Israel Air Force. Rolls-Royce to develop efficient next-gen jet engines for single-aisle aircraft The programme targets cleaner, more efficient engines for single-aisle aircraft. By Atharva Gosavi Transportation Oct 30, 2026 07:55 AM EST Jet engine. Stock photo. Wikimedia Commons Key Takeaways • UK and Rolls-Royce have agreed on a £2.5 billion($3.3 billion), 10-year jet engine program. • The program targets cleaner, more efficient engines for single-aisle aircraft. • Advanced materials, robotics and AI are among the technologies to be developed. Cleaner, more efficient jet engines for single-aisle passenger aircraft are the focus of a $3.3 billion (£2.5 billion) program agreed between the UK government and Rolls-Royce, with joint funding spread over 10 years. Announced on October 28 alongside the Budget, the agreement aims to develop jet engine technologies and sustain British aerospace manufacturing over the coming decades. The investment is expected to support 3,300 existing jobs over the next few years, with the potential to create tens of thousands of additional roles in the longer term. Rolls-Royce estimates that securing a UK engine for the single-aisle aircraft market could attract billions of pounds in further investment and add $161 billion (£120 billion) to the economy over the program’s lifetime. Those figures remain projections tied to securing that market opportunity. Targeting single-aisle aircraft The program will focus on jet engines for single-aisle aircraft, the passenger planes commonly used on routes between Britain and European destinations. The government’s Industrial Strategy identifies this market as the UK aerospace sector’s biggest opportunity over the next 50 years. The agreement seeks to position British industry to compete for that demand while maintaining the capabilities needed to develop and manufacture commercial aircraft engines. “This is a landmark moment for the UK’s aerospace industry. This is a once-in-a-generation opportunity to lay the foundations for decades of sustainable economic growth across the UK, creating high-value jobs and transforming the country’s advanced manufacturing supply chain,” said Rolls-Royce chief executive Tufan Erginbilgic. Embraer names FL Technics as new Authorized Service Center for E-Jets in Lithuania Published October 29, 2026 Vilnius, Lithuania, 29 October 2026 – Embraer has named FL Technics, a leading global provider of aircraft maintenance, repair, and overhaul (MRO) solutions, as an Embraer Authorized Service Center (EASC) for its commercial aircraft operating in Lithuania. The authorization covers the E170 and E190 jets, further expanding the company’s service portfolio in regional aircraft support. Services will be provided at FL Technics’ facilities in Vilnius and Kaunas. With extensive experience and deep technical know-how in maintaining narrowbody aircraft, FL Technics leverages proven processes, best practices, and cross-platform engineering capabilities, to deliver greater efficiency, faster turnaround times, and optimized maintenance solutions for Embraer operators across the continent. “We are pleased to welcome FL Technics to Embraer’s global network of Authorized Service Centers,” said Frank Stevens, Vice President of Global MRO Centers of Embraer Services & Support. “Their proven maintenance capabilities and growing presence across Europe will provide E-Jet operators with greater access to high-quality support solutions. This partnership reinforces our commitment to delivering the best customer experience and ensuring our customers can operate with confidence wherever they fly.” “We are honored to become an Embraer Authorized Service Center”, said Saulius Bajarunas, CEO of FL Technics. “This recognition is a strong validation of our technical capabilities, quality standards, and customer-focused service model. We look forward to supporting Embraer operators with reliable and efficient MRO services from our global network. This milestone further strengthens the relationship between Embraer and FL Technics. Since the launch of Line Maintenance services for Embraer aircraft in 2023, FL Technics has developed a robust operational footprint, delivering Line Maintenance support across key European stations, including Vilnius (VNO), Palanga (PLQ), Bergen (BGO), Oslo (OSL), Trondheim (TRD), Bucharest (OTP), Cluj-Napoca (CLJ), Bodø (BOO), and Ålesund (AES). Image: https://embraer.bynder.com/share/048F8AA5-DC99-4803-A16A4217B34DA904/ About FL Technics FL Technics is a global provider of aircraft maintenance, repair, and overhaul (MRO) services, operating across Europe, Asia Pacific, Middle East and the Americas. Certified under EASA Part-145 and Part-147, the company offers a wide range of services including base and line maintenance, component support, engineering, and technical training. Its capabilities now officially include Embraer E170-190 aircraft. FL Technics employs over 4000 aviation professionals and operates MRO hangars in Lithuania, the United Kingdom, Indonesia, and the Dominican Republic. The company is part of Avia Solutions Group – the world’s largest ACMI provider – and is continuously investing in state-of-the-art infrastructure, technology, and workforce development to meet the evolving needs of the global aviation market. About Embraer A global aerospace company headquartered in Brazil, Embraer operates in the Commercial Aviation, Executive Aviation, Defense & Security and Agricultural Aviation segments. The Company designs, develops, manufactures and markets aircraft and systems, and provides after-sales Services & Support to customers. Since its foundation in 1969, Embraer has delivered more than 9,000 aircraft. On average, every 10 seconds, an aircraft manufactured by Embraer takes off from somewhere in the world, transporting more than 150 million passengers annually. Embraer is a leading manufacturer of commercial jets up to 150 seats and the main exporter of high value-added goods in Brazil. The company maintains industrial units, offices, service centers and parts distribution, among other activities, in the Americas, Africa, Asia and Europe. Navy Class A Aviation Mishaps Reach Decade High The Navy recorded 16 Class A aviation mishaps in fiscal 2026. Amelia Walsh Wednesday, October 28, 2026 at 03:52 PM ET Verified Edited By: Matt Ryan U.S. Navy [Photo By Seaman Kaitlyn Bailey] Key Takeaways: The U.S. Navy recorded 16 Class A aviation mishaps and 11 afloat mishaps in fiscal year 2026, according to data reported by USNI News on Oct. 27. Both totals were the highest in at least a decade, raising questions about the safety record across naval aviation and ship operations. The 16 aviation mishaps occurred between Oct. 1, 2025, and Sept. 30, 2026, and included manned and unmanned aircraft incidents as well as ground aviation mishaps. The Navy last recorded more aviation mishaps in fiscal 2014, when there were 17. Of the 16 incidents, two involved unmanned aircraft. Among the 14 involving manned aircraft, 11 were flight mishaps and three occurred on the ground. The incidents included the loss of an F/A-18F Super Hornet and an MH-60R Seahawk in separate crashes into the South China Sea in October 2025. Two EA-18G Growlers also crashed during an airshow in May 2026, with all four aviators ejecting safely. A separate Growler landing mishap aboard USS Dwight D. Eisenhower in September injured four sailors. Another incident involved an MH-60S helicopter assigned to USS George H.W. Bush that ditched into the Arabian Sea, killing an aviator. Class A mishaps are the most serious category in the Navy’s reporting system. They include incidents involving at least $2.5 million in damage, destruction of an aircraft, a fatality or permanent total disability. By comparison, the Marine Corps repo rted six aviation mishaps during the same fiscal year, one more than in fiscal 2025. Five occurred in flight and one on the ground. The figures were reported by USNI News based on data from the Navy Safety Command. The Navy has not publicly attributed the increase in aviation mishaps to a single cause. FAA Orders DA40 Door Inspections After In-Flight Separations New airworthiness directive affects nearly 1,000 U.S.-registered Diamond aircraft. Matt Ryan Monday, November 02, 2026 at 03:54 PM ET Verified Edited By: Zach Vasile A Diamond DA40 at Holloman Air Force Base. [U.S. Air Force photo by Senior Airman Joshua Turner] Key Takeaways: The FAA has issued a new airworthiness directive covering all Diamond DA40, DA40 F and DA40 NG aircraft following multiple reports of passenger doors separating during flight. Published Monday, the directive affects an estimated 987 U.S.-registered airplanes and requires inspections, updated operating procedures and corrective actions to address potential door-latching failures. Door Separation Reports According to the FAA, Diamond Aircraft attributed some incidents to improperly secured passenger doors coupled with attempts to then latch them in flight. Diamond has not identified a definitive cause for the other instances. The FAA warned that a separating door could damage the aircraft’s structure, potentially leading to loss of control in-flight. Similar concerns prompted FAA action in 2010 following 31 reported door separations involving earlier DA40 models. Three commenters asked the FAA to exclude newer aircraft from the directive, arguing that updated secondary safety latches addressed the problem. The agency rejected those requests. “The FAA, in working with Transport Canada and DAI, has determined that the secondary safety latch does not resolve the unsafe condition and that the unsafe condition is not limited to older serial-numbered airplanes,” the agency stated. “The Model DA 40 NG is the latest model, and it has experienced several occurrences of door separation.” Required Inspections The directive will go into effect on Dec. 7 and requires operators to revise their aircraft flight manuals and complete initial inspections within 100 flight hours or 100 days, whichever comes first. Required checks vary according to aircraft time in service and include door latches, safety hooks, hinges, springs and related components. Operators must also install placards and perform applicable corrective actions, including component replacements when necessary. The FAA estimates that the initial inspection will cost approximately $331 per aircraft, plus $85 for flight manual revisions. Certain findings may require additional inspections or repairs, including replacement of the gas spring or safety hook assembly. The agency described the directive as an interim measure and said additional rulemaking may follow as Diamond continues investigating the underlying problem. Boeing still awaits major 777-9 test approvals despite 2027 delivery target Boeing still lacks Federal Aviation Administration approval for major portions of the 777-9 flight-test campaign, even as the manufacturer continues to target the widebody jet’s first delivery in 2027. Boeing CEO Kelly Ortberg said on October 27 that the remaining work includes extended-range twin-engine operations testing, while the company’s third-quarter update maintained that the program is on track for delivery next year. The tension is in the sequence. Boeing has received what Ortberg called some incremental authorisations for additional flight testing from the FAA, but it has not secured permission to begin the balance of the program. “We still have these big flight tests yet ahead of us,” he said during the earnings call. That leaves Boeing defending a delivery target while two linked approvals remain unfinished: authorization to conduct the final major tests and FAA acceptance of a redesigned seal inside the aircraft’s GE Aerospace GE9X engines. Boeing said in an October 27 securities filing that it expects approval for the final flight-test phases before year-end. A small engine component has become a certification gate The GE9X issue centers on its mid-seal, which proved less durable than expected. GE Aerospace redesigned the component and is seeking FAA approval for the change before the end of 2026. The company has been delivering engines equipped with the upgraded seal to Boeing since August, reflecting its confidence in the redesign, but production installation and regulatory approval are separate milestones. An FAA official said on October 20 that the agency will not issue the 777-9 type certificate until the redesigned mid-seal is certified. FAA Administrator Bryan Bedford also connected the component directly to the test campaign: “Flight testing and especially ETOPS isn’t going to get where it needs to be without resolving the seal issue.” ETOPS, short for extended-range twin-engine operations, is the approval framework that allows a twin-engine airliner to operate on routes that can take it far from a suitable diversion airport. For a long-range widebody, this is not a peripheral capability. It affects the kinds of intercontinental routes airlines can schedule and requires evidence that the aircraft and its systems meet the applicable operational standards. The seal therefore sits on the critical path in two ways. Its redesign requires approval as part of the engine installation, and the unresolved issue limits how far the extended-range test effort can progress. Boeing declined to elaborate on the seal’s effect on flight testing, and Ortberg did not address the component during the October 27 earnings call. Production is continuing ahead of the remaining tests Boeing is building approximately one 777-9 per month and expects to hold that rate through most of 2027. Chief financial officer Jay Malave said the company plans to deliver 10 to 15 aircraft in 2027. That schedule can coexist with unfinished testing because aircraft can move through production before certification, but they cannot enter customer service until the required approvals are secured and individual delivery conditions are met. This approach preserves manufacturing continuity, yet it also increases the importance of configuration control. Aircraft assembled before certification may need to incorporate the final approved hardware and any other changes resulting from testing. The evidence does not establish what modifications, if any, the already-produced 777-9s will require, but the production count will continue growing while the certification sequence remains open. Boeing’s financial planning assumes certification by mid-2027, although Ortberg said the company is pushing for an earlier approval. That provides some schedule room between the company’s hoped-for certification timing and its stated delivery year, but the margin depends first on the FAA authorizing the remaining tests and approving GE’s seal redesign. The immediate milestone is now year-end 2026. Both Boeing’s expected authorization for the final test phases and GE Aerospace’s target for approval of the redesigned mid-seal converge on that window. Until those decisions arrive, the 777-9’s 2027 delivery plan remains intact on paper while its largest remaining flight tests are still waiting for permission to proceed. FAA issues directive to address Boeing 737 circuit breaker issue By David Shepardson February 25, 20263:16 PM CSTUpdated February 26, 2026 WASHINGTON, Feb 25 (Reuters) - The Federal Aviation Administration said on Wednesday it has issued an airworthiness directive for all Boeing (BA.N), opens new tab 737 MAX 8 and 8200 airplanes to address a circuit breaker issue that could lead to a malfunction causing excessively high temperatures in the cabin and flight deck. The directive requires revising the airplane flight manual within 30 days to provide the flight crew with operating procedures if a certain circuit breaker trips, causing an air conditioning malfunction. The FAA said the directive covers 2,119 airplanes worldwide, including 771 U.S.-registered airplanes. The Misinformation Monitor newsletter rounds up international misinformation narratives, with a "Real or Fake?" quiz in every edition. Sign up here. Boeing said it supports the directive that mandates guidance it issued last month. "We are advancing an engineering solution to eliminate the possibility of this electrical fault," Boeing said. The FAA said two incidents in flight were recently reported in which temperatures increased sharply on board the airplane. Boeing said the root cause is a ground wire fault in the air conditioning system. The FAA said the air conditioning system malfunction could cause an uncontrollable, excessively high temperature, which "could lead to injury or incapacitation of flightcrew and passengers, which could result in the inability to maintain safe flight and landing." Boeing said it expects the fix to be ready for the 737 MAX 7 and 10 before certification and does not anticipate this issue to affect the certification timeline. Southwest Airlines (LUV.N), opens new tab, which had one of the reported incidents, said it is in close contact with the FAA and Boeing about the issue and has notified its flight crews about the steps that should be taken to respond to the specific electrical fault. US Air Force wants AI to assist aerial refueling By Michael Peck Oct 23, 2026 Follow on Google A KC-46A Pegasus tanker practices refueling operations on another KC-46A, Oct. 21, 2023. (Airman 1st Class Simonne Barker/Air Force) The U.S. Air Force is looking to artificial intelligence to improve the performance of its aerial refueling crews. The goal is for AI to automatically analyze refueling operations from cameras mounted on the tankers and provide “hot wash” feedback to the tanker crews. According to an Air Force Small Business Innovation Research solicitation, the service wants a system that can “leverage advanced computer vision, machine learning, and aviation (flight dynamics) analytics techniques to automatically extract operationally relevant performance metrics from aerial refueling events, quantify deviations from desired flight profiles, and generate actionable post-flight feedback to improve aircrew proficiency, reduce human-factor-driven mishaps, and enhance mission readiness.” The application deadline is Nov. 25. The SBIR is focused on the KC-46 tanker, which will feature a remote vision system that will allow operators to remotely operate the refueling boom via cameras and a 3D display. Though the system has been plagued by teething problems, the Air Force says most will soon be resolved. The system would automatically track the tanker and refueling boom, as well as the receiving aircraft. It would measure a variety of data, including position, velocity, alignment and closure rate, and assess whether they deviate from nominal parameters. The Air Force hopes an AI-based assessment system will mitigate the biases inherent in human assessment of aerial refueling, which is among the most demanding tasks for aircrew. “Current aerial refueling training and post-flight assessment processes rely heavily on instructor observation, pilot self-assessment, manual video review, and subjective evaluation of performance,” the SBIR noted. The system would create visual displays to improve the performance of pilots of the aircraft receiving fuel, such as “graphic AI overlays, heat maps, event timelines, and immersive or interactive debrief environments.” It would also have the potential to integrate with other training systems, including virtual and augmented reality, simulators, mission rehearsal systems, and other computer-based training tools. The Air Force sees this as a prototype for future AI-based training systems. “The desired end state is an operationally demonstrated capability ready to implement for at least one type of receiver aircraft and that can support transition into existing aviation training ecosystems and provide a scalable foundation for future AI-enabled aviation performance assessment across the Department of Defense,” the solicitation reads. Curt Lewis