Flight Safety Information - November 10, 2026 No. 221 In This Issue : Airbus A350-1000ULR Shatters Guinness World Record With 24-Hour Nonstop Flight : Air France A350 Pilots Make Unauthorized Turn, Nearly Collide With American Airlines A321 : Incident: American B38M at Santa Ana on Oct 29th 2026, tail scrape on go around : Loss of control on takeoff fatal for Piper pilot : Incident: France A321 near Paris on Apr 27th 2025, degradation of flight controls to direct law : Antonov An-124-100 lost a part of fuselage at c. 200 feet over the runway : AI and digital transformation reshape aviation, but safety remains non-negotiable : Bell 206L-4 LongRanger IV suffered an engine failure pilots made an emergency landing : FAA Housekeeping: Foreign Instrument Procedures, Approach Chart Clutter : Calendar of Events Airbus A350-1000ULR Shatters Guinness World Record With 24-Hour Nonstop Flight The Qantas Project Sunrise aircraft flew 12,503 nautical miles non-stop from Melbourne to Toulouse in 24 hours and 24 minutes. By Bhavya Velani November 9, 20265 Mins Read cle.Note: See photos and graphics in the original article, TOULOUSE– Airbus has secured a Guinness World Record for the longest flight by distance by a commercial airliner after its A350-1000ULR completed a non-stop test flight from Melbourne Airport (MEL) to Toulouse-Blagnac Airport (TLS) on July 27 and 28, 2026. The Airbus-operated flight covered 12,503 nautical miles (23,155 kilometres) in 24 hours and 24 minutes. The ultra-long-range aircraft is being developed for Qantas Airways (QF) under Project Sunrise, which aims to connect Sydney with London and New York through non-stop flights. Airbus A350-1000ULR Completes Record-Breaking Test Flight Airbus operated the record-setting flight under the callsign AIB35LR as part of the A350-1000ULR flight test campaign. The aircraft departed Melbourne at 5:27 pm local time on Monday, July 27, and arrived in Toulouse at 9:51 am local time on Tuesday, July 28. The aircraft travelled 12,503 nautical miles, equivalent to approximately 23,155 kilometres, during the journey. The flight lasted 24 hours and 24 minutes, demonstrating the aircraft’s endurance and long-range capabilities. The flight also formed part of Airbus’ efforts to meet Qantas’ requirements for Project Sunrise. The manufacturer had to operate a sector with a block time of 23 hours, measured from aircraft pushback at departure until arrival at the parking position. The test was designed to simulate the operational demands of the longest commercial flights that Qantas plans to introduce with the A350-1000ULR. Aircraft Crosses Three Continents and Two Oceans After departing Melbourne, the aircraft flew over Sydney before heading northeast across the Pacific Ocean towards Los Angeles. It crossed the International Date Line before continuing over the North American continent. The aircraft then crossed the Atlantic Ocean, headed south towards the United Kingdom, flew over London and continued to Toulouse in southwestern France. During the journey, the aircraft crossed three continents and two oceans. The extended flight also allowed the crew to witness two sunsets and two sunrises. Thirteen People Participated in the Record Flight A total of 13 people were on board the A350-1000ULR during the record-setting flight. The team included three Airbus flight test pilots, two Qantas pilots, five Airbus flight test engineers, two Airbus design engineers and one representative of the International Aeronautical Federation. The Airbus flight test pilots were Xavier Pepin, Vincent Sibelle and Josef Bayoud. Qantas was represented by Captain Andrew Coull and Captain David Summergreene. The Airbus engineering team included Laurent Rossignol and Nicolas Granier as test flight engineers, alongside flight test engineers Tuan Do, Alexia Plumet and Jaime Angoloti Airbus Highlights A350-1000ULR Achievement Lars Wagner, Chief Executive Officer of Commercial Aircraft at Airbus, described the record as an important achievement for the manufacturer and its Project Sunrise partnership with Qantas. He said the flight had fully demonstrated the A350-1000ULR’s ability to undertake extremely long commercial journeys while maintaining an efficient operating model. Wagner also acknowledged the contributions of Qantas, Rolls-Royce and other partners involved in developing the aircraft. Photo: Airbus How Airbus Extended the A350-1000ULR’s Range The A350-1000ULR is a specialised version of the standard A350-1000, designed to support ultra-long-haul operations from Australia’s east coast to major international destinations. One of its most important modifications is an additional Rear Centre Tank (RCT) integrated into the aircraft’s structure. The tank provides approximately 20,000 litres of additional fuel capacity and extends the standard A350-1000’s range by around 1,000 nautical miles. The aircraft also features an increased maximum take-off weight and is powered by two Rolls-Royce Trent XWB-97 engines. These modifications allow it to operate routes approaching 10,000 nautical miles with flight times of up to 22 hours. The additional fuel capacity also provides the necessary range for diversion requirements at the end of lo Qantas Project Sunrise: Sydney to London and New York Qantas ordered 12 Airbus A350-1000ULRs under Project Sunrise to introduce non-stop flights between Australia’s east coast and major international destinations. The airline plans to launch daily non-stop services between Sydney and London from October 2027. These flights will operate as QF1 and QF2, marking the first time Qantas will connect the two cities without an intermediate stop. The first aircraft, named Vega, is scheduled for delivery in April 2027. Qantas plans to sell tickets for the Sydney-London service from February 2027. The airline’s Sydney-New York non-stop service is expected to follow from mid-2028, with tickets scheduled to go on sale from August 2027. Each Project Sunrise A350-1000ULR will accommodate 238 passengers across four cabins: CabinSeatsFirst Class6Business Class52Premium Economy40Economy Class140Total238 The configuration gives more than 40% of the aircraft’s seats to premium cabins. Qantas has also designed a dedicated Wellbeing Zone between the Premium Economy and Economy cabins to allow passengers to stretch, hydrate and move around during the extremely long journeys. In addition to the 12 A350-1000ULRs, Qantas has ordered another 12 standard A350-1000 aircraft for its future long-haul network. Photo: Cam Wallace LinkedIn Airbus A350 Family Continues to Expand The A350-1000ULR is the fourth passenger variant of the Airbus A350 family. The existing passenger line-up includes the A350-900, A350-900ULR and A350-1000. Airbus has developed the A350 family around improved fuel efficiency, reduced carbon emissions and enhanced passenger comfort for long-haul operations. At the end of October 2026, the A350 family had accumulated 1,628 orders from 70 customers. More than 740 aircraft were already operating with 42 airlines worldwide, primarily on long-haul routes. The family is also expanding into the cargo market through the A350F freighter. The aircraft completed its maiden flight on September 29, 2026, beginning a planned nine-month flight test campaign. The A350-1000ULR’s record-setting journey marks another milestone in Airbus’ long-range aircraft development programme. It also brings Qantas closer to introducing non-stop flights between Australia and Europe and North America under Project Sunrise. Stay tuned with us. Further, follow us on social media for the latest updates. Join us on Telegram Group for the Latest Aviation Updates. Subsequently, follow us on Google News Air France A350 Pilots Make Unauthorized Turn, Nearly Collide With American Airlines A321 An unauthorized left turn by an Air France A350 triggered an ATC traffic alert after it crossed the departure path of an American Airlines A321 at LAX By Helen William November 8, 2026 9 Mins Read Note: See photos, graphics and videos in the original article. LOS ANGELES- An Air France (AF) Airbus A350-900 and an American Airlines (AA) Airbus A321 came within 400 feet (121 meters) of vertical separation shortly after departing Los Angeles International Airport (LAX) on November 7, 2026. An unauthorized turn by the Air France aircraft triggered a traffic alert, forcing air traffic controllers to intervene to prevent a potential mid-air collision. Air France Flight AF28 was heading to Papeete (PPT), while American Airlines Flight AA1660 was operating to Dallas/Fort Worth International Airport (DFW). Both aircraft received immediate instructions from air traffic control (ATC) to change course and maintain separation. Neither flight reported injuries, and both continued to their intended destinations. Air France A350 and American A321 Avoid Collision The incident involved an Air France Airbus A350-900, registered F-HUVK, and an American Airlines Airbus A321-200, registered N191UW. Both aircraft departed Los Angeles International Airport within approximately one minute of each other during the early hours of Saturday, November 7. According to available flight information, Air France Flight AF28 departed at approximately 12:15 AM local time for Papeete, French Polynesia. American Airlines Flight AA1660 followed at approximately 12:16 AM, operating to Dallas/Fort Worth in Texas. The two aircraft had different departure instructions designed to maintain safe separation during their initial climb. However, the Air France aircraft reportedly deviated from its assigned departure procedure shortly after takeoff, placing it on a conflicting flight path with the American Airlines aircraft. The aircraft came within approximately 400 feet (121 meters) of vertical separation, according to the incident account. Considering the size of the two wide- and narrow-body aircraft and their combined passenger capacity, the situation required immediate intervention from air traffic controllers. Photo: Leaderofthewave. | Wikimedia Commons https://commons.wikimedia.org/wiki/File:Air_france_airbus_a350_f-htya.jpg Unauthorized Air France Turn Triggers Air Traffic Control Alert The Air France Airbus A350-900 was cleared for takeoff from Runway 24L at Los Angeles International Airport. The aircraft was assigned the SUMMR2 Standard Instrument Departure (SID), which establishes the required flight path for departing aircraft. According to the Federal Aviation Administration (FAA), the SUMMR2 departure procedure requires aircraft departing from Runways 24L/R and 25L/R to initially climb straight ahead before following the assigned route. Meanwhile, American Airlines Flight AA1660 was instructed to maintain an altitude of 2,000 feet to allow the Air France aircraft to complete its departure and turn safely. However, according to aviation commentator TurbineTraveler on X, the Air France aircraft made an unauthorized left turn shortly after departure instead of following the assigned SUMMR2 procedure. The deviation brought the A350 into the departure path of the American Airlines A321, creating a loss-of-separation event. The departure controller quickly identified the developing conflict and issued immediate instructions to both aircraft. Air France Flight AF28 received an instruction to turn immediately to a heading of 270 degrees, while American Airlines Flight AA1660 was instructed to maintain 2,000 feet. The controller also issued a traffic alert to the American Airlines crew, warning them about the Air France aircraft approaching from their 12 o’clock position at less than one mile. Photo: By Steven He – https://www.flickr.com/photos/192971287@N07/51175590378/, CC BY-SA 4.0, https://commons.wikimedia.org/w/index.php?curid=105229339 ATC Audio Reveals Emergency Instructions and Pilot Deviation The air traffic control audio provides further details about how controllers managed the situation and restored separation between the two aircraft. After issuing the immediate heading instruction to Air France, the controller questioned the crew about its departure clearance. The exchange revealed that the Air France aircraft had been instructed to follow the SUMMR2 departure rather than turn directly onto a separate heading. The controller repeatedly asked the crew to confirm which departure procedure it had received from the tower. The Air France pilots eventually confirmed that they had been instructed to fly the SUMMR2 departure. The controller subsequently advised the crew of a possible pilot deviation and provided a telephone number for further communication. Meanwhile, American Airlines Flight AA1660 received additional instructions to maintain its assigned altitude before being cleared to climb to 17,000 feet and continue its flight. The controller also apologized to the American Airlines crew for the incident, explaining that the other aircraft had turned in front of them despite receiving instructions to follow the correct departure procedure. The exchange highlighted the importance of clear communication between pilots and air traffic controllers during busy departure operations. Photo: Tim | Flickr Air France and American Airlines Flight Details Both aircraft eventually received clearance to continue their journeys after ATC resolved the conflicting flight paths. Flight detailsAir FranceAmerican AirlinesFlight numberAF28AA1660AirlineAir France (AF)American Airlines (AA)DestinationPapeete (PPT)Dallas/Fort Worth (DFW)Departure airportLos Angeles (LAX)Los Angeles (LAX)Departure time12:15 AM12:16 AMDateNovember 7, 2026November 7, 2026AircraftAirbus A350-900Airbus A321-200RegistrationF-HUVKN191UW Neither aircraft reported injuries or damage associated with the incident. Both flights continued toward their respective destinations following the intervention. ATC and Pilots Comms Here’s a detailed transcript of communication between pilots and LAX ATC as flagged by You Can See ATC and recorded by LiveATC.net: [00:05] ATC: Air France 28 Heavy, RNAV Del Rey, wind 330 at 3, Runway 24L, cleared for takeoff. [00:12] Air France 028: RNAV Del Rey, cleared for takeoff, Runway 24L, Air France 028. [00:27] ATC: Air France 28 Heavy, contact SoCal Departure. [00:30] Air France 028: SoCal Departure, Air France 028 Heavy, good night. [00:36] ATC: Air France 028 Heavy, good evening. [00:36] Air France 028: Passing 1,500, climbing 5,000. [00:44] ATC: Air France 028 Heavy, SoCal Departure, radar contact. Climb via SID. [00:48] Air France 028: Climbing via SID, Air France 028. [00:55] American 1660: American 1660, we are at 2,000, climbing 5,000. [01:01] ATC: Air France 028 Heavy, fly heading 270 immediately. [01:05] Air France 028: Heading 270 immediately. [01:09] ATC: American 1660, SoCal Departure, traffic alert. Traffic 12 o’clock, less than a mile. Maintain 2,000. [01:15] American 1660: Okay, we’ll go back to 2,000, American 1660. [01:20] ATC: Air France 028 Heavy, you were instructed to climb via SID, not to turn to a heading. [01:28] Air France 028: Copy, Air France 028. [01:29] ATC: Air France 028 Heavy, why did you turn to a heading? [01:32] Air France 028: Standby. [01:34] ATC: Thank you. [01:37] ATC: Air France 028 Heavy, what departure were you instructed to fly? [01:42] Air France 028: Standby one. [01:44] Air France 028: Standby two, standby one. [01:48] Air France 028: We were… give me a minute. [01:53] ATC: No problem, Air France 028 Heavy. [01:57] ATC: American 1660, climb and maintain 17,000, maintain 250 knots. [02:03] American 1660: 250 knots, 17,000, American 1660. [02:10] ATC: Air France 028 Heavy, proceed direct DART, resume climb via SID. That’s the SUMMR2 departure, sir. [02:18] Air France 028: Resuming SUMMR2 departure via SID. And which direct DART? [02:27] ATC: DART. [02:28] Air France 028: DART, yes, sorry. Roger that, Delta, Alpha, Romeo, and Romeo, Kilo, Air France 028 Heavy. And just to confirm, you were on the SUMMR, correct? [02:38] ATC: You were instructed by the tower to fly the SUMMR2 departure, correct? [02:44] ATC: Air France 028 Heavy, I need an answer, sir. [02:52] Air France 028: Air France 028 Heavy, how can you hear? [02:55] Air France 028: Sorry, go ahead, Air France 028. [02:58] ATC: All right, Air France 028 Heavy, climb and maintain [altitude unclear in supplied transcript], and I need an answer. What departure were you instructed by the tower to fly? [03:06] Air France 028: Okay, climbing [altitude unclear]. We were cleared, we were instructed to fly SUMMR2 departure. [03:14] ATC: Air France 028 Heavy, thank you very much. [03:16] ATC: Possible pilot deviation. I have a number for you to call when you’re ready. [03:24] Air France 028: We repeat the number, go ahead. [03:28] ATC: Stand by. [03:30] ATC: Air France 028 Heavy, it’s… [03:35] Air France 028: Air France 028. [03:36] ATC: Air France 028 Heavy, thank you very much. Contact Los Angeles Center on 119.05. [03:42] Air France 028: 119.05, bye-bye, sir. [03:45] ATC: Bye. [03:47] ATC: American 1660, sorry about that. [03:49] ATC: That aircraft just turned in front of you. [03:52] ATC: They were instructed they were on the right departure, but, you know, pilot deviation. [03:57] ATC: Proceed direct DOTS. [03:59] American 1660: Okay, direct DOTS, American 1660. Great job, thank you. [04:05] ATC: No problem. Photo: Anna Zvereva | Flickr Similar American Airlines Incident Occurred at LAX in 2025 The latest incident is not the first time an American Airlines aircraft has been involved in a reported loss-of-separation event at Los Angeles International Airport. In 2025, an American Airlines aircraft and an ITA Airways aircraft reportedly came dangerously close to each other after a pilot deviation during their departure from LAX. The incident also required intervention from air traffic controllers, who issued instructions to prevent the two aircraft from entering conflicting flight paths. Both incidents highlight the importance of pilots following assigned departure procedures, particularly at airports with complex runway configurations and high volumes of departing and arriving traffic. Photo: Los Angeles World Airport Complex Departure Procedures at Los Angeles International Airport Los Angeles International Airport is one of the busiest airports in the United States, handling substantial domestic and international traffic throughout the day. Its departure procedures help controllers maintain separation between aircraft operating on different routes, particularly during periods of heavy traffic. The SUMMR2 Standard Instrument Departure is designed to guide aircraft away from the airport before they transition to their assigned en-route flight paths. The procedure is particularly relevant to westbound departures heading toward destinations across the Pacific, including Hawaii, Asia, and other international markets. Aircraft departing from Runways 24L/R and 25L/R must initially follow the prescribed straight-ahead climb before making subsequent turns according to their assigned departure instructions. In this incident, the reported unauthorized left turn by the Air France A350 brought it into conflict with the American Airlines A321 departing from Runway 25R. The departure controller identified the developing conflict and issued immediate instructions that allowed both aircraft to change course and restore separation. The incident demonstrates how closely coordinated pilot actions and air traffic control instructions help prevent potentially serious accidents during busy airport operations. Stay tuned with us. Further, follow us on social media for the latest updates. Join us on Telegram Group for the Latest Aviation Updates. Subsequently, follow us on Google News Incident: American B38M at Santa Ana on Oct 29th 2026, tail scrape on go around By Simon Hradecky, created Monday, Nov 9th 2026 16:16Z, last updated Monday, Nov 9th 2026 16:16Z Note: See video in the original article. An American Airlines Boeing 737-8 MAX, registration N335SN performing flight AA-806 from Dallas Ft. Worth,TX to Santa Ana,CA (USA), was on short final to Santa Ana's runway 20R when the aircraft initiated a go around at very low height, however, the tail contacted the runway surface during the go around. The aircraft climbed to 3000 feet, positioned for another approach to runway 20R and landed without further incident about 13 minutes later. The FAA reported: "AIRCRAFT EXPERIENCED A TAIL STRIKE DURING GO-AROUND." The aircraft returned to service about 14 hours after landing. https://flightaware.com/live/flight/AAL806/history/20261030/0009Z/KDFW/KSNA Loss of control on takeoff fatal for Piper pilot By General Aviation News Staff July 5, 2025 · The airport manager, who was also the owner of the FBO at the airport in Churchville, Maryland, where the Piper PA-28R-200 was based, reported that he spoke with the pilot the morning of the accident. He told investigators that the pilot was frustrated that the new interior for the airplane had taken so long to be installed as he was planning to leave the next day to have the airplane’s avionics upgraded. He added that the purpose of the flight was for the pilot to complete some flights in the airport traffic pattern with a new propeller installed before the long cross-country flight the following morning. The airport manager left the airport about 1850 as the pilot was completing his preflight inspection of the airplane. A mechanic for the FBO reported that he spoke with the pilot just before the accident flight and that the pilot told him about the upcoming trip to Florida the next day and that he wanted to take the airplane for a test flight just to make sure it was performing normally before the long cross-country flight. The mechanic also reported that he had fueled the airplane’s wing tanks to the “tabs” the day before the accident, as the fuel had been drained to facilitate a new weight and balance calculation due to maintenance that had been recently completed. The mechanic did not witness the airplane start, taxi, or takeoff as he had already left for the day. An earwitness who lived near the airport, and was outside doing yard work, reported that about 1905 he heard an airplane start its takeoff roll and that he did not hear the airplane perform an engine run-up. He stated that Runway 1 was in use, and that when this runway was being used airplanes in the traffic pattern would usually bank left and pass over his house. He reported that the sound from the engine was normal, and that the RPM tone did not change for the duration of the flight. Another witness, the only witness to see the airplane in flight, reported that he was outside in his yard when he saw the airplane in a steep left bank with the wings perpendicular to the ground. He said that he could only see the underside of the airplane, that the landing gear appeared to be down, and that it was much lower than usual. The earwitness reported that the entirety of the flight lasted about 45 seconds from when he first heard the airplane to when he heard it hit the ground. The pilot died in the crash. No track data was available either from air traffic control primary radar targets or from ADS-B. Both the airport manager and the mechanic reported that early in the day the weather had been poor, but that it had become better as the day progressed. A witness reported the weather was clear with a light breeze out of the north. He said it was “a perfect evening to fly.” The Piper PA-28R-200 Pilot’s Operating Manual (POM) recommended short- and soft-field takeoffs be performed with flaps set to the 25° position. The POM made no mention of taking off with the flaps set to the full 40° position. The POM listed the stall speeds for the landing gear-down, flaps 40° setting to be 64 mph with 0° of bank, 66 mph with 20° of bank, 73 mph with 40° of bank, and 90 mph with 60° of bank. The POM also stated that the best rate of climb with the landing gear down was obtained at 95 mph and the best angle of climb was obtained at 85 mph with the landing gear down. No data was available to determine the expected rate of climb with the flaps set to full and the landing gear in the down position. Probable Cause: The pilot’s exceedance of the airplane’s critical angle of attack during initial climb, which resulted in an aerodynamic stall/spin and loss of control that the pilot did not recover from. NTSB Identification: 192711 To download the final report. Click here. This will trigger a PDF download to your device. This July 2023 accident report is provided by the National Transportation Safety Board. Published as an educational tool, it is intended to help pilots learn from the misfortunes of others. Incident: France A321 near Paris on Apr 27th 2025, degradation of flight controls to direct law By Simon Hradecky, created Friday, May 16th 2025 19:12Z, last updated Tuesday, Nov 10th 2026 19:22Z An Air France Airbus A321-100, registration F-GMZC performing flight AF-1749 from Malaga,SP (Spain) to Paris Charles de Gaulle (France), was descending towards Paris when the crew received a "F/CTL Stabilizer Jam". The crew declared PAN PAN, the crew used manual trim, the flight control law changed to alternate. Upon extending the landing gear the flight controls reverted to Direct Law. The aircraft continued for a safe landing on Charles de Gaulle's runway 08L. The French BEA rated the occurrence an incident and opened an investigation. The aircraft remained on the ground in Paris until May 5th 2025, then performed a test flight before returning to service. On Nov 10th 2026 the BEA released their final report in French (an English version will be released in due time) concluding the probable causes of the incident were: incorrect application of the F/CTL Stabilizer JAM procedure, inappropriate use of trim control in flight and landing with elevators close to the pitch-up stop. Following factors may have contributed: - lack of training in ALTERNATE mode with only manual trim control available - lack of clarity in the ECAM F/CTL STABILIZER JAM procedure, particularly for the item "TRIM FOR NEUTRAL ELEV" as displayed - the pilot monitorings inadequate supervision at a time when workload had intensified A misunderstanding of the ECAM F/CTL STABILIZER JAM procedure probably led the pilot flying to rely on a more familiar course of action regarding the manual use of the trim tab, namely that set out in the F/CTL DIRECT LAW procedure in DIRECT mode. The semantic similiarity between the item "MAN PITCH TRIM ... USE" in the latter and "MAN PITCH TRIM ... CHECK", which was displayed to the crew during the incident, was such as to foster confusion. Antonov An-124-100 lost a part of fuselage at c. 200 feet over the runway Date:Tuesday 10 November 2026 Time:16:02Type: Antonov An-124-100M Owner/operator:Antonov Airlines Registration:UR-82007 MSN:19530501005 Year of manufacture:1986 Fatalities:Fatalities: 0 / Occupants: Other fatalities:0 Aircraft damage:Minor Location:Nagoya/Chubu Centrair International Airport (NGO/RJGG) - Japan Phase:Take off Nature:Cargo Departure airport:Nagoya/Chubu Centrair International Airport (NGO/RJGG), Japan Destination airport:Angeles City-Diosdado Macapagal International Airport (CRK/RPLC) Confidence Rating: Information is only available from news, social media or unofficial sources Narrative: An Antonov An-124-100 lost a part of fuselage at c. 200 feet over the runway while takeoff from Nagoya/Chubu Centrair International Airport. No reported injuries. The runway was closed for an hour. This Ruslan had been reported a fire incident while landing at Chubu Centrair at the night of 22nd October. Sources: https://www.tokai-tv.com/tokainews/feature/article_20261110_49262 https://x.com/sputnik_jp/status/2120098452436885682 https://flyteam.jp/photo/4538442 https://article.auone.jp/8e82fbfe-139b-4c90-8ad4-cacbeb5be55a https://www.flightradar24.com/2026-11-10/07:00/20x/34.86,136.79/13 https://www.flightradar24.com/2026-10-22/10:20/20x/34.85,136.81/12 https://globe.adsbexchange.com/?icao=50801b&lat=30.450&lon=135.279&zoom=5.5&showTrace=2026-11-10&trackLabels History of this aircraft Other occurrences involving this aircraft 11 May 2021 UR-82007Antonov Airlines0São Paulo-Guarulhos International Airport, SP (GRU/SBGR)nonRunway excursionMedia: Revision history: Date/timeContributorUpdates10-Nov-2026 13:05 UTCisamuelAdded10-Nov-2026 15:47 UTCCicjosUpdated [Narrative, ]10-Nov-2026 17:41 UTCASNUpdated [Aircraft type, Cn, Destination airport, Source, Embed code, [Corrections or additions? Edit this accident description] AI and digital transformation reshape aviation, but safety remains non-negotiable Story by Joana Mourão Carvalho 6 min read Note: See video in the original article. Artificial intelligence and digital transformation are opening up new possibilities for commercial aviation, from personalising the passenger experience to forecasting operational disruption. But the modernisation of a highly regulated sector demands changes that go far beyond technology, argue two executives from Hitit, a Turkish provider of technology solutions for the aviation industry, in an interview with Euronews during the World Aviation Festival (source in Portuguese), in Lisbon. For Aras Kubilay, who is responsible for industry engagement and business development at Hitit (source in Portuguese), aviation is facing a structural shift in the way it manages its digital systems. The challenge is to modernise the infrastructure underpinning day-to-day operations without compromising flight continuity and passenger satisfaction. "Airlines are extremely complex businesses and they operate continuously, 24 hours a day, seven days a week," he said. That means they cannot simply shut down operations for several days to replace their core IT systems. The scale of the challenge becomes even clearer when set against the pace of digital transformation. According to Kubilay, airlines are well aware that they need to change, but many still struggle to take the first steps. He cited survey data collected from industry executives last year: 72% regarded digital transformation as crucial. This year, he said that during the WAF he had heard estimates that the share has risen above 90%, although he stressed that he does not have an updated official figure. Even so, only 27% of airlines are thought to have taken concrete action. Related video: Boeing could replace 2 airline pilots with 1 - aviation safety experts have concerns (Mentour Pilot) "If we do not move in this direction in the next two to three years, we could face problems," he warned. Instead of attempting to replace an entire infrastructure in one go, Kubilay advocates a phased approach, allowing carriers to pinpoint specific issues and roll out incremental improvements. "You do not start with a major overhaul all at once. You replace parts as needed and then, if the results are positive, you keep going in that direction," he explained. Where is AI adding value in aviation? Artificial intelligence sits at the heart of this transformation, but its use needs to be tied to concrete objectives. In Kubilay's view, airlines must first decide whether they want to increase revenues, cut costs or improve the customer experience before launching new projects. "If they say they are going to do everything at once, simply by adding an AI label, they will spend money and nothing will happen", he cautioned. Hitit says it already embeds AI tools in different components of its solutions, including cost accounting, reporting and the management of operational disruption. Nevra Onursal Karaağaç, the company's CEO, explained that these applications can make users' work easier, allowing them, for example, to obtain reports by submitting written requests, without having to manually enter multiple parameters. The technology can also help to anticipate weather-related problems affecting flights. Kubilay described a model that combines physical characteristics of runways, their orientation to the wind and weather patterns to predict situations in which a flight may have to be rescheduled. With that information, airlines can anticipate potential delays or reroutings, instead of reacting only once a disruption has already occurred. Technology can help anticipate weather-related problems affecting flights AP Photo Despite these possibilities, he warned of the risks of relying blindly on AI systems, especially in customer service. Without naming the airline, he referred to a case where an artificial intelligence system is said to have allowed refunds above the amount paid and changes to flights that should not have been authorised. "In such a sensitive and complex sector as air transport, it may be necessary to think twice," he noted. Safety, he stressed, must not be sacrificed in the name of convenience. Systems need to be configured with clear rules and limits on what they can do, with appropriate control mechanisms remaining in place. Karaağaç also emphasised that developing technology for aviation requires more than programming skills. "You need to understand the aviation world itself," she said, arguing for collaboration between industry consultants, business analysts and development teams. The spread of artificial intelligence is also changing the way passengers search for and purchase flights. For Kubilay, this shift could be an opportunity for airlines to regain control over their relationship with customers, in a market where flight comparison sites and digital intermediaries tend to make price and schedule the central factors in travellers' decisions. As AI assistants become more widespread, passengers may start to search for trips through conversational queries, specifying not only their destination but also the purpose of their journey or their preferences. That information and context could help airlines put forward more relevant offers, instead of presenting a long list of undifferentiated options. "If they do not control customer engagement, it is very easy to swap one airline for another," he argued. Kubilay believes personalisation can benefit both passengers, who will save time finding what they are looking for, and airlines, which will be able to offer products better tailored to each person's needs. Even so, the transformation should preserve the familiarity of these digital platforms. When systems are modernised, the aim should not be to force passengers to learn how to use apps and platforms all over again. "Ideally, people should not be able to tell that anything has changed. The only things they should notice are that everything works better and has become simpler," he explained. A future without check-in? One change that Kubilay sees as feasible in the coming years is the elimination of check-in as a distinct step in air travel. He recalled that the process dates back to the era of paper tickets, when part of the document had to be torn off to confirm its use. Despite digitalisation, some of those practices remain embedded in today's systems. "We want to abolish check-in completely. You buy your ticket, go to the plane and that is it," he explained. Bringing that vision to life will, however, depend on the co-operation of the entire industry. Verifying passengers' identity, border controls and security requirements involve different entities and cannot be solved by a single company in isolation. Kubilay highlighted an initiative developed using standards set by the International Civil Aviation Organization (ICAO) and promoted by the International Air Transport Association (IATA), called Digital Travel Credentials (DTC), which aims to facilitate the use of digital identity credentials. The goal is to cut down on the need for passengers to repeatedly present and validate the same information throughout their journey. According to him, an IATA study found that, on a typical trip, passengers have to provide the same information seven times. "We have to show our ID when we make the booking, when we check in baggage, when we board the plane, when we go through customs. Then again when we land. Why can I not do this just once and the authorities communicate among themselves?" he asked. The Digital Travel Credentials (DTC) initiative is a secure digital version of the passport designed to make border checks faster and simpler AP Photo Any reduction in these steps will nonetheless have to respect security requirements. Kubilay explained that digital credentials can be verified through digital signatures and confirmation of their authenticity by the issuing authorities. The aim is to simplify travel without compromising the safety of passengers and operations. Hitit seeks to consolidate international expansion Founded in 1994 by two women, Hitit started out developing passenger loyalty solutions and progressively expanded its activity to core reservation systems, ticketing, check-in and other airline operations. The company now develops solutions covering a range of operational needs, including schedule planning, operations control, accounting, cargo and travel agency systems. According to Karaağaç, Hitit worked with 17 airlines in 2018 and, in 2026, provides services to nearly 70 carriers. The most recent public figures cited by the Turkish firm's CEO point to 68 airlines in 47 countries, with its solutions used at more than 900 airports. "Although our roots are in Turkey and the company was founded in Turkey, we are already a global business," Nevra Karaağaç underlined. Hitit became a company listed on the Istanbul stock exchange in 2022. For Karaağaç, international expansion will continue to be based on close relationships with airlines and the ability to adapt to their needs. Kubilay, for his part, argues that the future of aviation technology will depend on more interoperable systems that allow airlines to combine solutions from different providers without being locked into a single partner. Operators should avoid situations in which they lose control of their own data or find themselves unable to switch provider. "Technology must be compatible with the future," he cautioned, explaining that companies need flexibility to adapt to changes they cannot yet foresee. Looking ahead to the next five years, Kubilay expects digital transformation, the modernisation of commercial systems and the adoption of AI to reach a sufficiently broad scale to become the industry norm, while maintaining safety, operational continuity and passenger trust, even if the sector's most ambitious goals are not achieved within the original deadlines. This text was translated with the help of artificial intelligence. Report a problem : [feedback-articles-en@euronews.com]. Bell 206L-4 LongRanger IV suffered an engine failure pilots made an emergency landing Date:Tuesday 10 November 2026 Time:13:51 UTC Type: Bell 206L-4 LongRanger IV Owner/operator:Meridian Helicopters LLC, opf FlyNYONRegistration:N217MH MSN:52226 Year of manufacture:1999 Fatalities:Fatalities: 0 / Occupants: 2 Other fatalities:0Aircraft damage:Substantial Category:AccidentLocation:Bayonne pier, Kearny, NJ - United States of America Phase:En route Nature:Test Departure airport:Kearny-HHI Heliport (65NJ), NJ Destination airport: Confidence Rating: Information is only available from news, social media or unofficial sources Narrative: The Bell 206L-4 LongRanger IV suffered an engine failure about four minutes after takeoff from the Kearny-HHI Heliport (65NJ), New Jersey. The pilots made an emergency landing on Bayonne pier, during which main rotor blads severed the tail. METAR: METAR KEWR 101351Z 23010KT 10SM SCT140 BKN190 BKN250 10/03 A2999 RMK AO2 SLP153 T01000033 $ICAO Occurrence Category: SCF-PP: System/Component Failure or Malfunction (Powerplant) Sources: https://x.com/snnfinalnd/status/2120213988453568714?a=tsOLO3mj9AnMxQmyhCs&s=20 https://newjersey.news12.com/tour-helicopter-makes-hard-landing-on-bayonne-pier-after-engine-goes-out https://globe.adsbexchange.com/?icao=a1d49e&lat=40.689&lon=-74.107&zoom=13.7&showTrace=2026-11-10&trackLabels FAA Housekeeping: Foreign Instrument Procedures, Approach Chart Clutter 9 July, 2025 FAA Housekeeping: Foreign Instrument Procedures, Approach Chart Clutter By Chris Shieff Note: See graphics and photos in the original article. Recently, the FAA has been doing some spring cleaning. You might have missed them, but recent changes to the FAA’s advisory circulars and charting notices are quite important. This article covers two of them: • Effective June 2025, the FAA officially shifted the responsibility for evaluating and approving foreign instrument procedures to aircraft operators themselves. • From October 2, instrument approach charts will be decluttered by removing unnecessary comms data. Let’s take a look at each of these in more detail. Removing approvals for specific foreign procedures Recently, the FAA advised those operating under Part 91(K), 121, 125 and 135 of changes to foreign instrument procedure authorizations. It has removed outdated references to specific foreign instrument procedures by title from operator authorizations (OpSpec C058, C358 and H107). Others were simplified (C059, C060, and C384) to remove references to specific foreign airports and procedures. The end result? Operators are no longer required to obtain FAA approval for specific foreign instrument procedures listed by name — but they must still hold the required FAA authorization (OpSpec, MSpec, or LOA) to conduct the type of procedure (e.g., RNP AR, CAT II/III), regardless of where it’s flown. So, does this mean I can now fly any foreign procedure without FAA involvement? Not quite. While you no longer need FAA approval for each individual foreign procedure, you still need FAA authorization for the procedure type and must comply with host country requirements. For instance, if Germany requires local authorisation for an RNP (AR) approach into EDDM/Munich, you must obtain it without FAA involvement. ICAO (Annex 6) says operators are still required to obtain approvals when the host state mandates it, and crews must comply with any local procedures or limitations. Why the change? Without delving too much into the specifics, there are a few reasons: • Less paperwork – foreign procedural reviews are cumbersome and labor intensive, and lead to delays in approval. • Less workload – inspectors no longer have to approve each foreign procedure individually. • Improved design – there has been significant improvement in procedural design around the world thanks to the proliferation of ICAO PANS OPS. • Empowerment – operators can perform their own risk assessments and use globally standardised instrument procedures without the extra weight of FAA approvals. So the onus is now on the operator – what next? That’s where AC 120-105B comes into play. It provides guidance for US operators on reviewing and accepting foreign instrument procedures outside the US. This includes a list of your areas of responsibility, recommended tools and checklists to help with your review, and advice on incorporating a review process into your company’s manuals, SOPs and pilot training. If you operate abroad, it’s important you’re familiar with this revised AC. We’ve also put together the following checklist based on its advice to help get you started: Click to download PDF. De-cluttering Approach Charts On July 3, the FAA issued a new charting notice (advance notification of significant changes to charts and publications). The news is that from October 2, the FAA will begin removing redundant comms data from instrument approach charts. This includes departure ATIS, CLNC DEL and the availability of CPDLC if all of this is shown on the corresponding airport diagram. Listing it again on instrument approach charts is unnecessary and can reduce readability during critical phases of flight while critical frequencies remain prominent (don’t worry, tower and ground ain’t going anywhere). While we have you, a couple more FAA-related tidbits to brush off the table. • Notams. Big changes are coming to the US system. By September, it will be completely overhauled. The new system will be a fast, cloud-based, and (hopefully) rock-solid stable. A renewed focus on improved safety throughout the US NAS has escalated the project, and the targets are ambitious – user testing is expected to start later this month. • FAA-license holders abroad. This is our last reminder! July 7 has come and gone, which means anyone holding US licences/ratings and living outside of the US must have provided a US based address for service to the FAA via the USAS portal. If you haven’t yet, your license is effectively now invalid until you do – whatever you do, don’t operate an aircraft while un-licensed. Have we missed a spot? CALENDAR OF EVENTS . Airlines 2026 conference - November 11, 2026 (London) . Bombardier Safety Standdown (November 10–12, 2026 in Wichita, KS) . CHC Safety & Quality Summit - 11th – 13th November 2025 - Vancouver, BC Canada . AIN Corporate Aviation Leadership Summit (CALS) Mx November 16, 2026 Savannah, Georgia . Aircraft Fire Hazards, Protection, and Investigation 17 to 19 November 2026, Woburn MA . 2027 ACSF Safety Symposium - April 6-8, 2027 - ERAU Daytona Beach, FL Curt Lewis